Logo

B1239 Engine Trouble Code

B1239 Engine

When you check engine light came on code B1239 the reason should be . However your vehicle's manufacturer may have a different definition for the B1239 OBD-II Diagnostic Body (B) Trouble Code. So you should chech it on our car models.

B1239 if your catalytic convertor fails completely, you eventually won't be able to keep the car running its engine. Your gas mileage will also be not working properly, so you should try and fix it as soon as you can. Unfortunately, the average replacement cost is around $2,500 and you can't do it yourself unless you're an experienced mechanic service for your car.

B1239 Code Meaning :

B
OBD-II Diagnostic Body (B) Trouble Code For Engine
1
Fuel And Air Metering
2
Ambient Air Temperature Sensor Circuit Low
3
Cold Start Injector 1 Malfunction
9
Ignition Coil A Primary/Secondary Circuit Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

B1239 OBD-II Diagnostic Body (B) Trouble Code Description

B1239 engine trouble code is about Ignition Coil A Primary/Secondary Circuit Malfunction. Ambient Air Temperature Sensor Circuit Low and Cold Start Injector 1 Malfunction causes most of code B1239.

Reason For B1239 Code

The reason of B1239 OBD-II Engine Trouble Code is Ambient Air Temperature Sensor Circuit Low.

B1239 code on vehicles with electronically controlled automatic transmissions, the 3-4 shift solenoid is responsible for actuating the hydraulic circuits to activate clutches or bands that change gears inside the automatic transmission in your car.

How To Repair B1239 Code

Before starting let's see B1239 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access B1239 code stored in the ECU.
  • Technicians will note B1239 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

The fluid pressure sensor provides the PCM with the data necessary to monitor the transmission performance. If the fluid pressure increases, the electrical voltage reading from the pressure sensor will increase; if the pressure decreases, the voltage decreases.

This process helps the mechanic narrow down the exact cause of the issue. If the transmission fluid fix did not cause the code to disappear from the PCM, then next step is to inspect the electrical components, and to continue working through possible repairs until the correct issue is found.

Sometimes B1239 code comes with B123900 code.

Diagnosis Of Engine Error OBD Code B1239

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a B1239 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the B1239 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.
The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.